|
HYAZ
TM Inkjet Media
1) Copy/Print on to the coated
side of the media using a compatible Inkjet Printer.
2) To prevent a paper jam,
make sure the vinyl is not bent, warped, or corners folded BEFORE loading.
Loading by hand ONE SHEET at the time (pressing FF/Ready) is a way to
make sure it loads correctly.
3) When gluing a vinyl label
to any surface, clean the surface and remove residual grease, soot, or
dust.
4) It is not recommended (on
larger labels like 11" X 17") to remove all the back paper before installing.
It’s better to remove the paper from a small area at one end first such
as a 1/2" vertical strip at the left hand or right hand edge.
5) Line up your label. When
the position looks correct, let the label make contact with the surface
on the edge where you removed the back paper.
6) Now bend the label back
and carefully remove the rest of the protective back paper, and glue the
label down working from the end you glued first. Then work your way towards
the other end holding that end away from the surface. You can use your
finger or a sponge and only press down (glue) a small area each time to
prevent trapping air bubbles. Do not use excessive pressure when working
the label to prevent smudging the ink.
7)
If the label is used outdoors you
must use clear spray and overlaminate.
The Overlaminate must be applied in such way that it prevents water from
contacting the label. Clear enamel spray is available here or in most
hardware or automotive parts stores.
You can spray the label before
you apply it (after printing) to prevent over spray. Fixative spray is
available in most craft stores or you can use the clear spray offered
here or sold in most automotive parts stores.
Use our WOL overlaminate together
with the spray. Using clear spray as
the only protection will offer limited water proofing.
To extend UV
resistant of Inkjet media HPS offers overlaminate with built in UV barrier.
Printing and Application Instructions
| Item # |
IVF8511GC 10 sheets pack |
| Media |
Self Adhesive Vinyl |
| Media Type |
Inkjet |
| Color |
Clear / Transparent |
| Printers |
Most Desk Top |
| Type of Adhesive |
Permanent. |
|
CANON 600 SERIES
Media Choice:
High Res. Paper
Print Quality:
Photographic Print
Normal Resolution
|
CANON 4000 SERIES
Media Choice:
High Res. Paper
Quality: Photographic
Resolution:: Standard
|
EPSON PHOTO EX
& PHOTO 700
Media Type: 360
dpi Ink Jet Paper
Print Quality:
Photo
|
EPSON 400, 600,
700, 800, 1520, 3000, 5000 SERIES
& STYLUS PHOTO
Media Type: 360
dpi Ink Jet Paper
Print Quality:
Photo
|
EPSON 400, 600,
700, 800, 1520, 3000, 5000 SERIES
& STYLUS PHOTO
Media Type: 360
dpi Ink Jet Paper
Print Quality:
Photo
|
HEWLETT PACKARD
600, 700, 800, 1000 & PHOTOSMART PRINTERS
Media Type: Premium
Ink Jet Paper
Print Quality:
Normal
|
Printer Settings
If your printer
is not listed here then select transparency and normal resolution.
For complete updated list of
our media and to order on line go to
www.texascraft.com or call 817-489-5249
General:
If you are working with 4.25" x 11" vinyl
you can try removing all the backing material and then use the technique
described above.
NOTE:
If using self adhesive media, note that any adhesive may become difficult
to remove over time. If you want to use self adhesive media on automobiles
or other items where you don’t want the label to become permanent or difficult
to remove after long periods of time we recommend our selection of media
with removable adhesives.
Disclaimer: We
have tested our media in various personal inkjet printers with good results.
The user of this paper/film must determine the suitability of this product
before beginning production, using his equipment and method of application.
The sellers and manufactures maximum obligation shall be to replace paper/film
that has been found to be defective. Neither the manufacturer nor the
seller shall be held liable for any injury, direct or consequential, arising
out of the use of, or inability to use this paper/film.
home |
help| about us |
e-mail
HPS LLC. Copyright 2003-2007 texascraft.com
|
